- 30%


1,933.61 IVA esclusa

The Lombardi LC4 COMBO is a professional guitar valve amplifier, class A-B, designed and built in Italy by the Lombardi Amplification with high quality components. The amp is made with two types of wood. The outside is made of Poplar, that makes it very lightweight and with a warm sound. The fixing panel of the loudspeakers is made of Fir so that the harmonic board can have the best timbre.

Thanks to years of study and research in the history of Amplifier Lombardi it was possible to create the LC4 COMBO, a revolutionary tube circuit was perfected after 24 months of test…

While remaining in the top list of the handmade point-to-point amplifiers that are made with high quality components, this amplifier is something completely new!  Precise pre-amplifier with a unique and flexible tone, with only 5 controls, an infinite repertoire of sound.. How is that possible? We put 2 different tube pre-amplifier together!
A good amplifier with 80w of dynamic .

The cabin has hand-made Lombardi Custom Amplifier

There are many other features that make this amplifier a new dream!
There it is the new Lombardi LC4”

Categories: , Product ID: 3063


The Guitar Valve Amplifier COMBO 1×12 ″ was built in Italy Point-to-Point with Biconic speaker.

A couple of words on the Tubes and the Reverberation:

The Pre-amplifer tube is a EF86 NOS, a pentode that has a high gain, a precise and defined sound, a balanced frequency range (and that is the reason why it is in the tube Hi-Fi) and a unique timbre especially with clear and crunch sound.

The Hammond is controlled by a tube ECC83 Groove Tubes and by a ECL82 NOS.

The tubes that brings the sound of the Pre-amplifier to the Amplifier is an original ECC82 MULLARD NOS (this high quality tube makes the difference!).

The two pilot tubes are ECC83 Tungsol.

The output tubes are two new Mullard EL34, that sound really good!

A couple of words on the Transformers:

We use input and output transformers made especially for us, that are very like the one we used fifty years ago, big and heavy, oversize perfect for a real guitar valve amplifier!

This is the engine of the tube, we do not compromise on high performances!

A couple of words on the Tone Control:

The valve amplifier LC4 has an innovative tone control… high, low and medium were not enough! We used two independent section of the pre-amplifier and we joint them together:

BASS CHANNEL controls low, medium and volume.

The sound is focused on the low and medium pitch, the tone is simply controlled but in a very effective way you can control a clamorous punch and a Jazz definition!

HIGH CHANNEL has a default equalization and it is possible to control the volume.

The clear, biting sound that are missing in the first channel are emphasized by the volume control, not by a simple tone …

That is the key:

Two opposite sound that can be mixed together, as you wish. You almost have infinite sound combination… It is the same as having two amps and mixing the sound they make… you can test it!

A Master volume that controls the sound of the two channels, the saturation of the amplifier tubes and the volume. Moreover it diversifies the combination of the two channels and allows to control the saturation of the pre-amplifier tubes. In the rear panel there is a switch that increase the power from 60 W to 25 W and halve the tension of the amplifier tubes. The dynamics and the saturation of the tubes is faster and the compressor is higher.

It took months to develop this circuit and to obtain its ultimate expression… there is no need of a fx loop for a lot of pedals: the sound of each musician and their pedals goes through the main input, called “INPUT”, 0 db or 10 db for powerful signal… the amplifier does the rest!

A couple of words on the Speaker:

It took many attempts and tests we designed two different 12″ with two different timbre response:

A warmer and softer timbre, with a good balance and frequency extension… low pitch deep and precise a crystal clear sound that accurately reproduce all the harmonic.

The timbre reproduces clear sounds of any kind of music, from jazz to blues, to the folk and can be also unconventionally used to amplify from rhodes to sinth, to a voice filtered by the tubes!

The other timbre, more aggressive has a rock sound! With a clear and precise sound that never get lost, even in the most noisy stages and when there is the distortion the timber don’t dry out, the sound is clear and nothing get lost!

The choice is yours…

There it is a combo that will surprise every guitarist and phonic that will have the opportunity to use it!

Technical Description:

Valve amplifier with 1 guitar input that pilots two mixable channels

LOW CH control: low, medium, volume

HIGH CH control: volume

General volume

Volume reverberation

Switch that halves the anode current of the tubes from 80W to 25W

Pre-amplifier and amplifier with class A-B tube

Output power 25W / 80W

Tubes Amplifier:

  • Outputs: 2x EL34
  • Pilot: 2x ECC82

Tubes Pre-amplifier

  • Inputs: 1x EF86
  • Outputs: 1x ECC82
  • Reverberation: 1xECC83 1x ECL82

1 biconic Custom Lombardi 12″ speaker

Power supply 110/220-240 V 50 Hz

Product made of wood covered with artificial leather

1 leather handle

Support rubber feet

Loudspeaker protection

Fuse 2A

Dimensions cm [WxDxH] 54x30x46

Weight kg 25

  • Transport cover
  • Transport Flight case


Additional information

Weight 30 kg
Dimensions 65 × 40 × 55 cm


There are no reviews yet.

Be the first to review “GUITAR VALVE AMPLIFIER COMBO LC4 25 / 80W 1×12 ″”

Your email address will not be published. Required fields are marked *